Table of Contents
How do you enter ROMmon mode on a Cisco router 2800?
Press break on the terminal keyboard within 1 minute of power up in order to the router into ROMmon. Enter in confreg 0x2142 at the rommon 1> prompot in order to boot the from Flash. Type reset at the rommon 2> prompt. Type no after each setup question or press Ctrl+C to bypass all questions.
How do you enter ROMmon mode on a Cisco switch?
If the switch continuously reboots, press Control-C to prevent autoboot and to get into ROMmon mode.
How do I get out of Cisco ROMmon mode?
These are three ways the router can enter ROM Monitor (ROMmon) mode (rommon#>):
- Reload, initialize, or power cycle the router with the configuration register boot field set to 0.
- Reload, initialize, or power cycle the router without having a Cisco IOS Software image to boot from.
How do you enter ROMmon mode?
To manually boot into the ROMmon mode, you will need to reboot the device and break the boot sequence. Pressing the Ctrl+Break key combination during boot usually does this.
What is Confreg 0x2142?
0x2142 tells the router to bypass the configuration in NVRAM so that you can perform password recovery.
How do I boot a Cisco switch from USB to Rommon mode?
While the router is powered off, plug in the USB flash drive to the USB port on the router. Power on the router and when it starts to boot up press the Break key to enter ROMMON mode.
What does Flash_init command do?
Use the flash_init command to initialize the Flash filesystem of your Cisco Switch. List the content of the flash drive of your switch.
What does Rommon mode mean?
ROMMON mode is a router mode, not a mode within the Cisco IOS XE software. The ROMMON software and the Cisco IOS XE software are two separate programs that run on the same router. At any given time, the router is running one of these programs, but it never runs both at the same time.
How do I boot an image from Rommon?
Copy a bootstrap program from ROM into the RAM, run the bootstrap program. The bootstrap program looks for the first IOS image on the flash memory, extracts it into RAM and boots the IOS image. When there is no IOS image, it will boot into ROMMON.
What is the Break key for Cisco router?
Standard Break Key Combinations
| Software | Platform | Try This |
|---|---|---|
| Telnet | N/A | Ctrl-], then type send brk |
| Telnet to Cisco | IBM Compatible | Ctrl-] |
| Teraterm | IBM Compatible | Alt-b |
| Terminal | IBM Compatible | Break |
What is config Reg 0x2102?
The factory-default setting for the configuration register is 0x2102. This indicates that the router should attempt to load a Cisco IOS software image from Flash memory and load the startup configuration.
How do I change Confreg in Rommon?
There are two way to change Config Register on a router. This can be done both in Rommon mode and in configuration mode. In Rommon mode, it can be change with “confreg” command. Below, we are changing Configuration Register as 0x2142.
What is Rommon mode in Cisco?
The ROM Monitor (ROMMON) is a bootstrap program that initializes the hardware and boots the Cisco IOS XE software when you power on or reload a router. If your router does not find a valid system image to load when it is booting, the system enters the ROMMON mode.
What is the command to reset a Cisco switch?
Resetting the Cisco IP switch to factory defaults
- Reset the switch to factory defaults: Erase the existing configuration: write erase. Reload the switch software: reload.
- Save the configuration: IP_switch-A-1# copy running-config startup-config.
- Reboot the switch and wait for the switch to reload: IP_switch-A-1# reload.
What is config text Cisco?
Config. text is the left over config from the original design. Cisco wants to standardize the interface to make it all look like IOS. They tweak it and when the switch starts the config. text are copied and become the startup-config.”
What does Cisco Rommon do?
How do I boot a Cisco switch from USB to ROMmon mode?
What is Cisco ROMmon mode?
How configure config register in ROMmon?
In Rommon mode, it can be change with “confreg” command. Below, we are changing Configuration Register as 0x2142. After this configurationi we should reset the router to use this new value,or to force the router boot through this config register.
What value of 0x0 brings the switch to ROMMON mode?
The configuration register value of 0x0 always brings the switch to ROMmon mode. The typical configuration register is 0x2102, with the boot system flash command pointing to the system image to load
Why does my Cisco router keep booting up in ROMMON?
It goes back to ROMmon because the router’s Cisco IOS software image and bootflash image are both corrupt. Since you have already determined that the cause of the router booting up in ROMmon is not due to the configuration register value, the only option available for recovery is to re-install or upgrade the Cisco IOS software.
What instructs the router to boot into ROMMON?
– a setting of the config register instructs the router to boot into rommon Could you boot the router, capture and post the console output while it is booting? This would give us some insight into why it is booting into rommon.
Why won’t my Switch Switch to ROMMON mode?
Go to Solution. 12-13-2012 11:45 AM 12-13-2012 11:45 AM The configuration register has been changed incorrectly. The configuration register value of 0x0 always brings the switch to ROMmon mode. The typical configuration register is 0x2102, with the boot system flash command pointing to the system image to load